![pinner joint pinner joint](https://live.staticflickr.com/3224/3147175891_a62e396173_b.jpg)
Make sure that there is still some paper left at the end of the joint so you can seal it tight. You can add more bud if there is more space to fill. Use a packing tool such as a dabber or a pen to push the bud further in until it compresses tightly. You can increase the size of the joint further by adding more ground buds at the end of the joint. Just a few inches from the surface is fine. Do not drop from a high elevation, though. You may have to use your fingers to apply a bit of force to intensify the impact. Do this a couple of times until the bud is compressed fully. Drop the crutch tip on a hard surface and let the impact of gravity pack the bud. If there is not much paper left at the tip of the joint, you can use this technique. The paper may come off, and you have to start again. The centrifugal force created by the shaking motion will compress the joint and pack it. Gently shake the joint with your wrist back and forth. Make sure the glue strip is properly attached to the paper. If you have some paper left at the tip of the joint, pinch it with your fingers to keep the buds inside. An unevenly packed bud will have an irregular burn and will negatively impact your smoking experience. A packed bud is more likely to burn smoothly, slowly, and evenly. Doing this locks the crutch in place to avoid it slipping out accidentally.Īs soon as the joint rolls perfectly, you need to pack the buds to compress it further. Give the crutch a lick to make it stick to the rolling paper. This will compress the bud further to make it burn smoothly and evenly. Lightly push it in towards the bud to seal the gaps in between. Remember that you have left a third of the crutch sticking out of the paper. You have to seal the paper to hold the final shape of the joint. As soon as the paper’s tightly tucked, lick the glue strip on the flap and stick it immediately. The compression of the joint will determine how slow and how smooth the cannabis will burn. Start tucking at the crutch and onto the opposite end of the paper. Both these steps are crucial to forming a perfectly rolled cannabis. Now, roll the paper to form a straight cylinder or cone.
![pinner joint pinner joint](https://cdn.shopify.com/s/files/1/1588/2635/files/packrolltheperfectjoint_1024x1024.gif)
When the bud can hold the shape on its own, You’re ready for the next step. You have to keep rolling to compress the bud into the proper shape. The key is to move the paper with your fingers back and forth until you achieve a straight cylinder (pinner) or cone shape. Do not worry if you do not get it right the first time. Rolling the bud is a challenging step that requires the right pressure control. The buds should gradually increase towards the opposite end to form a cone shape. If you want to make a cone joint, you should have fewer buds at the side of the paper near the crutch. If you want to make a pinner joint, arrange the buds evenly across the length of the paper. There are two ways to arrange the bud depending on the joint shape you want to achieve. Arranging the ground bud makes it easier to roll the joint. Make sure that the bud is distributed on the surface of the paper before rolling. Grind the cannabis bud and arrange it evenly inside the rolling paper. Place it at the end of the rolling paper and let a third of it stick out. It makes it easier to roll a joint and hold on to it as you smoke. The rolling tip or the crutch is a cylindrical filter that you put at the tip of the rolling paper.
![pinner joint pinner joint](http://woodarchivist.com/wp-content/uploads/2016/07/1002-Pinned-Miter-Joint-1.jpg)
The Joint Rolling Processįirst of all, you need the proper supplies.
Pinner joint how to#
This article will discuss how to roll a joint and five unique ways to do it. However, just like any kind of art, you have to practice until you master the technique. You can create a masterpiece that you can show off to your friends. If you are tired of the regular joint or the typical joint, remember that the process is an art form every time you roll a joint. Others want to bring out their creativity by rolling a triple braid joint, a scorpion joint, or a plumber’s joint. Some want it simple with the classic cone, pinner, or cigarette-style joint. Everyone has their preferences when rolling joints.